 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Product Data Sheet PRELIMINARY VS-502 Voltage Controlled SAW Oscillator Features * Output frequencies from 300 MHz to 1350 MHz * Ultra low jitter < 0.2 ps-rms (12 kHz to 20 MHz) < 0.2 ps-rms (50 kHz to 80 MHz) * Low phase noise, -160 dBc/Hz @ 1 MHz offset (1 GHz) * Small low profile 9.0 * 14.0 * 4.5 mm SMT package * 3.3 V, 5.0 V and 12V Supply Options * LV-PECL, PECL, or Sinewave (0 to +10 dBm into 50 ) * Output disable feature (For LVPECL - PECL option) Product is free of lead and compliant to EC RoHS Directive Applications * Point to Point / Point to Multi Point Radios * Instrumentation * PLL Frequency Translation * Test & Measurement * Military & Avionics Description The VS-502 is a SAW based voltage controlled oscillator that operates at the fundamental frequency of the internal SAW resonator. This direct approach enables this series to achieve low phase noise and jitter performance at high output frequencies and over wide operating temperature range. The oscillator is housed in a hermetically sealed J-lead surface mount package offered on tape and reel. As an option, it has an output disable to facilitate on-board test Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 1 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Table 1. Electrical Performance Parameter Symbol Minimum FN APR 300 50 Typical Maximum 1350 20 10 10 + 350 200 VCC VCC VCC ICC PO PO PO PO 11.4 4.75 3.135 12 5 3.3 55 12.6 5.25 3.450 70 Units MHz ppm % % % ppm/V ppm V V V mA dBm dBm dBm dBm dBc ps,rms ps,rms V V ps % k kHz C mm Notes 1,2 9,2,3 4,2,9,3 4,2,9,3 4,2,9,3 2,8 6,9 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 2,3 7,6 7,6 2,3,5 2,3,5 2,3,5 2,3,5 6 6 1,3 Frequency Center Frequency Absolute Pull Range Linearity (+12V Supply) Linearity (+5V Supply) Linearity (+3.3V Supply) Gain Transfer Temperature Stability (-40C to +85C) Supply Voltage (B) Voltage (C) Voltage (D) - PECL Output Only Current (No Load) Output- Sinewave Options Sinewave, into 50 (G) Sinewave, into 50 (H) Sinewave, into 50 (J) Sinewave, into 50 (K) Harmonics Jitter @ 622.08 MHz (12 kHz to 20 MHz) Jitter @ 622.08 MHz (50 kHz to 80 MHz) 0 +3 +7 +10 -20 0.10 0.10 VOL VOL tR,tF SYM ZC BW TOP VCC-1.63 VCC-0.98 45 104 200 49/51 110 100 See Ordering Table 9.0 x 14.0 x 4.5 350 55 115 Output- PECL Logic Option (F) Output Level Low Output Level High Rise & Fall Time Symmetry (Duty Cycle) Control Voltage Input Impedance Modulation BW (Driven from Low Impedance) Operating Temperature Package Size Table Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. See Standard Frequencies and Ordering Information Parameters are tested with production test circuit Parameters are tested at ambient temperature with test limits guard-banded for specified operating temperature. Measured as the maximum deviation from the best straight-line fit, per MIL-0-55310. Output levels are standard 100K PECL compatible and measured from 20% to 80% of a full output swing (Fig 1). Not tested in production, guaranteed by design, verified at qualification. Integrated across 12 kHz to 20 MHz, or 50 KHz to 80 MHz per GR-253-CORE Issue3. Tested with Vc = 0.3V to 3V for 3.3V supply, Vc = 0.5V to 4.5 V for 5V supply, Vc = 0.5V to 11.5V for 12V supply Maximum frequency occurs at room temperature Table 2. Typical Single Side-Band Phase Noise (dBc/Hz) for Sinewave Output Output Frequency 640 MHz 1000 MHz 100 Hz Offset -75 -65 1 kHz Offset -110 -95 10 kHz Offset -135 -125 Tel: 1-88-VECTRON-1 2 100 kHz Offset -150 -150 Website: www.vectron.com 1 MHz Offset -160 -155 Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator tR 80% Vcc - 1.3V 20% Vcc - 1.6V tF SYM = 100 x tA / tB Vcc - 1.0V tA tB Figure 1. 100K PECL Waveform Outline Diagram 6 5 4 Pad Layout VS-500-LFF-GNN VS-502-BJF-GNN XXX.XXX XXX.XXX VI YWW VI YYWW 1 2 3 8.890.15 [0.3500.006] 7.63 [0.300] 1.27 [0.050] 13.970.20 [0.5500.008] 0.460.05 [0.0180.002] [ 4.49+0.20 -0.30 +0.008 0.177-0.012 ] 3.00 [0.118] 8.80 [0.346] 2.54 [0.100] 5.08 [0.200] mm [inch] 5.080.13 [0.2000.005] 2.540.13 [0.1000.005] mm [inch] Table 3. Pin Out - PECL Option Pin 1 2 3 4 5 6 Symbol VC OD GND Output COutput VCC Function VCSO Control Voltage N/C or Output Disable1 Case and Electrical Ground VCSO Output VCSO Complementary Output Power Supply Voltage Table Notes: 1. By setting Output Disable pin high, the RF output is disabled and pin 4 is held high, pin 5 is held low. The threshold for Output Disable is 2.3V above pin 3. Output disable pin can be left floating for normal operation Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 3 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Suggested Output Load Configurations - PECL Operation +5.0V .01uF .1uF (From PLL) Vc OD Gnd 1 2 3 6 +5.0V +5.0V Vcc 120 120 5 COutput Output 4 82 (AC Coupling) 82 +5.0V .01uF .1uF (From PLL) Vc OD Gnd 1 2 3 6 Vcc (AC Coupling) 4 5 COutput Output 330 330 Suggested Output Load Configurations - LVPECL Operation +3.3V .01uF 0.1uF (From PLL) Vc OD Gnd 1 2 3 6 +3.3V +3.3V Vcc 130 130 4 5 COutput Output (AC Coupling) 82 82 +3.3V .01uF 0.1uF (From PLL) Vc OD Gnd 1 2 3 6 Vcc (AC Coupling) 5 COutput Output 4 240 240 Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 4 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Table 4. Pin Out - Sinewave Option Pin 1 2 3 4 5 6 Table Notes: Symbol VC VEE Output VCC VCC Function VCSO Control Voltage N/C Ground VCSO Sinewave Output Vcc21 Vcc1 1. If Vcc1 is +12V and a separate 5V is not applied to pin 5 then pin 5 must be connected through a 220 1/4W external resistor. Suggested Output Load Configurations - SINEWAVE Operation +12V Vcc From PLL 1 NC 2 3 6 5 4 220 1/4W 0.1uF 0.01uF 0.01uF Output AC Coupled with 50 to ground +5V Vcc From PLL 1 NC 2 3 6 5 4 0.1uF 0.01uF 0.01uF Output AC Coupled with 50 to ground Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 5 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Tape and Reel (EIA-481-2-A) Po F W ODo W2 C N A D P1 W1 B Tape Dimensions (mm) Dimension Tolerance VS-502 Reel Dimensions (mm) F Do Typ 1.5 W Typ 24 Po Typ 4 P1 Typ 12 A Typ 330 B Min 1.5 C Typ 13 D Min 20.2 N Min 100 W1 Typ 24.4 W2 Max 30.4 Typ 11.5 # Per Reel 200 Absolute Maximum Ratings Parameter Power Supply Voltage Control Range Storage Temperature Soldering Temp/Time Symbol VCC VC TS TLS Ratings VCC + 1.0V -0.5 to VCC +0.5V -55 to +125 +260/40 Unit V V C C/sec Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this datasheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Reliability The VS-502 family is capable of meeting the following qualification tests: Environmental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Conditions MIL-STD-883, Method 2002 MIL-STD-883, Method 2007 MIL-STD-883, Method 2003 MIL-STD-883, Method 1014 MIL-STD-883, Method 2016 Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 6 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Handling Precautions Although ESD protection circuitry has been designed into the VS-502 proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD Ratings Model Human Body Model Charged Device Model Minimum 1500 V 1000 V Conditions MIL-STD 883, Method 3015 JESD 22-C101 Reflow Profile (IPC/JEDEC J-STD-020) Parameter PreHeat Time Ramp Up Time Above 217 oC Time To Peak Temperature Time At 260 oC Ramp Down Symbol tS R UP tL t AMB-P tP R DN Value 60 sec Min, 180 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 20 sec Min, 40 sec Max 6 oC/sec Max 260 tL R UP tP R DN The device is designed to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements. The VS-502 device is hermetically sealed so an aqueous wash is not an issue. Termination Plating: Electroless Gold Plate over Nickel Plate Temperature (DegC) 217 200 150 tS t AMB-P 25 Time (sec) Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 7 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 VS-502 Voltage Controlled SAW Oscillator Available Standard Frequencies (MHz) 480 970 1344.3256 622.08 983.04 640 1000 672.1627 1090 696.4215 1200 938 1330 Other Frequencies Available Upon Request. Ordering Information VS - 502 - B J C - G N N - xxxx.xxxx Product Family VS: VCSO Frequency (See Above) 300 - 1350 MHz Package 502: 9 x 14 x 4.5 mm Input D: 3.3 V C: 5.0 V B: 12.0 V Other (Future Use) N: N/A Output F: G: H: J: K: PECL Sine 0 dBm Sine 3 dBm Sine 7 dBm Sine 10 dBm Other (Future Use) N: N/A Absolute Pull Range G: 50 ppm F: 32 ppm C: 20 ppm Operating Temperature C: 0C to +70 C D: -20C to +70 C F: -40C to +85 C For Additional Information, Please Contact: USA: Vectron International, 267 Lowell Rd, Hudson, NH 03051 . . . . Tel: 1-88-VECTRON-1 EUROPE: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +49 (0) 3328-4784-17 ASIA: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tel: +86-21-28909740 Fax: 1-888-FAX-VECTRON Fax: +49 (0) 3328-4784-30 Fax: +86-21-28909999 Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Vectron International, 267 Lowell Rd, Hudson NH 03051-4916 8 Tel: 1-88-VECTRON-1 Website: www.vectron.com Rev: 27January06 |
Price & Availability of VS-502-BHF-CNN-13443256
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |